Search results
运放参数的详细解释和分析-part20，建立时间 (Settling Time) Wayne Xu. Genius 9936 points. 相信关注运放建立时间的人不是特别多，但是运放的建立时间，对于其后的ADC至关重要。如一个16bits的ADC，它的一个LSB对应的电压范围是其满量程的15ppm, (百万分之十五) 。. 如果驱动 ...
Aug 31, 2024 · Similarly, when the output low is not low enough, a pull-down resistor can be used to lower the low level.
- eliminate saturation of output devices with zero input times closed loop in DC Analysis (i.e. negative Vos trying to driver output less than ground) Fig. 11.6: Measuring Zo in SPICE: Step 1 – Measure Aol The TINA SPICE results of our Aol Test are shown in Figure 11.7 and we see a low frequency Aol gain of 144.13dB or 16.0879MV/V.
在 我们的项目中、我们将使用 DP83620SQE/NOPB 以太网收发器 (RMII 模式)。. 在以太网的 DVT 测试部分、我们已经确定了 MDC 至 MDIO (输出)延迟时间相对于数据表的故障。. 我们观察到的最大延迟时间不是20ns、而是413ns 延迟时间。. 请找到随附的图像进行分析。. 我们还 ...
The uDMA UART TX. // channel is used to transfer a block of data from a buffer to the UART. // The data size is 8 bits. The source address increment is 8-bit bytes. // since the data is coming from a buffer. The destination increment is. // none since the data is to be written to the UART data register.
This control mode provides a balance between the fast transient response of non-linear control modes (D-CAPTM, constant on-time, etc.) and the broad capacitor stability of other externally-compensated, fixed-frequency control modes (VM, CM). Internally-compensated ACM provides a fixed, predictable frequency and a simplified compensation ...
C6678 SRIO loopback. 请问，6678SRIO自带的loopback例程怎么把内循环改为外循环？. 除了要把loopback模式设为normal模式外还要怎么改？. 你使用的是哪个例程？. 如果使用下面链接的keystone_srio可以支持如下模式测试. 可以通过修改SRIO_Loopback_Mode loopback_mode= SRIO_DIGITAL_LOOPBACK ...
Jun 19, 2024 · TMS320F28377D: CCS Theia例程编译报错. 您好，. 使用CCS Theia导入了28377D的相关例程，尝试编译时报错. "This project contains 1 unresolved buildable linked resource (s). The project may not build as expected." 尝试了多个例程都是这个错误，并且未对例程做任何修改，加载至工作区后直接点击 ...
Use the following routing and placement guidelines when laying out a new design for the USB physical layer (PHY). These guidelines help minimize signal quality and electromagnetic interference (EMI) problems on a four-or-more layer evaluation module (EVM). Place the USB PHY and major components on the un-routed board first.
I2R losses in the MOSFET times the MOSFET’s duty cycle: IN OUT DS(ON) 2 COND OUT V V P = I • R • (2) where RDS(ON) is @ the maximum operating MOSFET junction temperature (TJ(MAX)). The maximum operating junction temperature is equation can be calculated by using an iterative technique. Since R DS(ON) rises with T J and T J rises with P D
