Search results
运放参数的详细解释和分析-part20，建立时间 (Settling Time) Wayne Xu. Genius 9936 points. 相信关注运放建立时间的人不是特别多，但是运放的建立时间，对于其后的ADC至关重要。如一个16bits的ADC，它的一个LSB对应的电压范围是其满量程的15ppm, (百万分之十五) 。. 如果驱动 ...
Contents iii Contents 1 The Op Amp’s Place In The World 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assumptions. This Technical Brief makes the following assumptions: The power supply designer has already designed the power stage of the single phase buck converter. The last step to the design is the compensation network. The designer has at least a basic understanding of control systems theory.
- eliminate saturation of output devices with zero input times closed loop in DC Analysis (i.e. negative Vos trying to driver output less than ground) Fig. 11.6: Measuring Zo in SPICE: Step 1 – Measure Aol The TINA SPICE results of our Aol Test are shown in Figure 11.7 and we see a low frequency Aol gain of 144.13dB or 16.0879MV/V.
Other Parts Discussed in Thread: DAC5675A 最近要用DAC5675A芯片做数模转换，在芯片手册上，update rate最大为400MSPS，而output setting time的典型值为12ns，也就是说输入的数字信号12ns后才能转化为正确的模拟信号，那么update rate最大应该等于1000Msps
CCS使用dual time graph ，只能显示两个单波形. user4073852. Intellectual 352 points. 使用ADC采集两路数据，准备将两个波形显示在一张图上，好方便分析比较。. 选取dual time graph ，设置后两个波形显示在了两张图上，和single time一样。. 如何设置显示在一张图上呢，下面是我 ...
经过进一步调查，我发现在HDMI 2.0 模式下，TMDS181似乎将TMDS时钟频率除以4。. 例如，HDMI信号源配置为发送4K60信号。. 在这种情况下，正确的TMDS时钟频率是148.5 MHz，是4K60信号597 MHz像素速率的四分之一。. 使用示波器，我可以解决TMDS181的IN_CLK引脚问题，并看到FPGA ...
您好 Linda、 请参阅以下回答： 问题1：为什么选择"S+H 持续时间、以便采样电容器充电至最终值的½ LSB 或¼ LSB 以内"？
The device also features a very fast current-sense-to-output delay time of. 35 ns and a ±1 A peak output current capability with improved rise and fall times for driving large external MOSFETs directly. The UCC38C4x family is offered in 8-pin packages, MSOP (DGK), SOIC (D) and PDIP (P). 7.
Nov 15, 2023 · Other Parts Discussed in Post: DRV8705-Q1 作者：Frank Qin Abstract 随着汽车电子的快速发展，汽车上很多电机的驱动方式已经从传统继电器逐渐演变成为MOSFET驱动的直流电机。同时，为了实现更高速和更精确的控制，现在对于MOSFET预驱的要求也逐渐变高...
